Vol. 2 No. 2 (2013): July-December 2013

Articles

• A Study on the Effect on Fuel Economy of a Two Wheeler by on Board Hydrogen Generation

  Gurpartap Singh, Kanwarpreet Singh, Harpreet Singh

  1-5

  • PDF

  314Views: 314 96Downloads: 96

• Evaluation and Characterization of Different Biomass Residues through Proximate & Ultimate Analysis and Heating Value

  Harmandeep Singh, Pawan Kumar Sapra, Balwinder Singh Sidhu

  6-10

  • PDF

  1393Views: 1393 650Downloads: 650

• Improvement in Hardness of LM-6 Aluminum Alloy Green Sand Castings by Taguchi Method

  Ravneet Kumar, Chandandeep Grewal

  11-18

  • PDF

  381Views: 381 97Downloads: 97

• Simultaneous Optimization of Multiple Quality Characteristics in Traveling Wire Electrochemical Spark Machining of Pyrex Glass

  Basanta Kumar Bhuyan, Vinod Yadava

  19-24

  • PDF

  315Views: 315 160Downloads: 160

• Study of Fluid Flow and Heat Transfer Through Mini-Channel Heat Sink

  Hemant Kumar, S. S. Sehga

  25-28

  • PDF

  576Views: 576 158Downloads: 158

• Evaluation of Drilling Performance of Unsaturated Polyester Resin

  S. Bandyopadhyay, S. Das

  29-34

  • PDF

  172Views: 172 96Downloads: 96

• Analysis of Kerf Taper Angle in Abrasive Water Jet Cutting of Makrana White Marble

  Vishal Gupta, M. P. Garg, R. Khanna, R. Khanna

  35-39

  • PDF

  670Views: 670 184Downloads: 184

• Effect of Various Parameters on Response Characteristics of WEDM during Machining of Al/SiCp-MMCs

  Harmesh Kumar, Alakesh Manna, Rajesh Kumar

  40-46

  • PDF

  560Views: 560 98Downloads: 98

• Optimum Design Parameters for Heat Transfer from Triangular Fin Array within a Rectangular Enclosure

  Debasish Das, Ankur Dwivedi, Swati Gupta

  47-51

  • PDF

  682Views: 682 151Downloads: 151

• Heat Transfer Enhancement by Using Nanomaterial in Phase Change Material for Latent Heat Thermal Energy Storage System

  A. T. Pise, A. V. Waghmare, V. G. Talandage

  52-57

  • PDF

  787Views: 787 154Downloads: 154

• Experimental Investigation of Fluid Flow and Heat Transfer in Microchannels

  Rajesh Sharma, Balkar Singh, Vijay Kumar Jadon

  58-62

  • PDF

  441Views: 441 146Downloads: 146

• A Study on Hybrid WECSM Setup During Cutting of E-Glass Fibre Epoxy Composite

  Anup Malik, Sushant Samir, Alakesh Manna

  63-68

  • PDF

  496Views: 496 131Downloads: 131

• Process Capability Analysis of MMC Prepared by Combining FDM, Vacuum Moulding and Stir Casting

  Rupinder Singh, Sardar Singh

  69-72

  • PDF

  687Views: 687 93Downloads: 93

• Characterisation of Biodiesel Derived From Waste Cotton Seed Oil and Waste Mustard Oil

  Sandeep Singh, Sumeet Sharma, S. K. Mohapatra, K. Kundu

  73-77

  • PDF

  285Views: 285 109Downloads: 109

• Optimisation of High Frequency Seam Welding Parameters By Taguchi Method

  Satish Garg, S. S. Banwait, Ravneet Kumar

  78-83

  • PDF

  713Views: 713 100Downloads: 100