Multi-Walled CNT Reinforcement to Thermal Spray Coatings
DOI:
https://doi.org/10.51983/ajeat-2018.7.2.948Keywords:
Hot Corrosion, Thermal Spraying, Carbon Nanotubes, Properties, ReinforcementsAbstract
Thermal spraying coating techniques have emerged as very effective surface protection technology to apply protective coatings for corrosion and wear resistance applications. These coatings have gained more importance in recent past. Advances in powder and wire production have resulted in development of various types of surface coatings with excellent wear and corrosion resistance properties. Because of excellent mechanical, thermal and electrical properties of Carbon Nanotubes, CNTs reinforced composite coatings are being developed for various applications, e.g. automotive, aerospace and sports equipment industry. It is observed that if properly deposited, these CNTs ceramic composite coatings can provide improved properties like wear and corrosion resistance. It has been found that CNTs composite coatings can be successfully deposited by thermal spraying techniques, and these coatings provide better performance than conventional coatings. This paper reviews the performance of such coatings developed by various researchers.
References
J. Lawrence and L. Li, "Surface treatment of an Al2O3-based refractory with CO2 and high power diode lasers for improved mechanical and chemical resistance characteristics," Surface and Coatings Technology, vol. 162, no. 1, pp. 93-100, 2003.
T. Sidhu, S. Prakash, and R. Agrawal, "Hot corrosion and performance of nickel-based coatings," Current Science, no. 90, 2006.
H. Singh, T. Sidhu, J. Karthikeyan, and S. Kalsi, "Evaluation of characteristics and behavior of cold sprayed Ni–20Cr coating at elevated temperature in waste incinerator plant," Surface and Coatings Technology, vol. 261, pp. 375-384, 2015.
R. Jones, "Hot Corrosion in Gas Turbines," DTIC Document, 1983.
N. Eliaz, G. Shemesh, and R. Latanision, "Hot corrosion in gas turbine components," Engineering Failure Analysis, vol. 9, no. 1, pp. 31-43, 2002.
A. López, M. Proy, V. Utrilla, E. Otero, and J. Rams, "High-temperature corrosion behavior of Ni–50Cr coating deposited by high velocity oxygen–fuel technique on low alloy ferritic steel," Materials & Design, vol. 59, pp. 94-102, 2014.
R. A. Rapp, "Hot corrosion of materials: a fluxing mechanism?," Corrosion Science, vol. 44, no. 2, pp. 209-221, 2002.
M. Kaur, H. Singh, and S. Prakash, "High-Temperature Corrosion Studies of HVOF-Sprayed Cr3C2-NiCr Coating on SAE-347H Boiler Steel," Journal of Thermal Spray Technology, vol. 18, no. 4, pp. 619-632, 2009.
R. Kumar, V. Tewari, and S. Prakash, "Studies on hot corrosion of the 2.25 Cr-1Mo boiler tube steel and its weldments in the molten salt Na2SO4-60 pct V2O5 environment," Metallurgical and Materials Transactions A, vol. 38, no. 1, pp. 54-57, 2007.
B. S. Sidhu and S. Prakash, "Evaluation of the behavior of shrouded plasma spray coatings in the platen superheater of coal-fired boilers," Metallurgical and Materials Transactions A, vol. 37, no. 6, pp. 1927-1936, 2006.
A. Vardelle and S. Kuroda, "Coatings under severe conditions," Journal of Thermal Spray Technology, vol. 16, no. 1, pp. 1-2, 2007.
B. S. Sidhu and S. Prakash, "Studies on the behaviour of stellite-6 as plasma sprayed and laser remelted coatings in molten salt environment at 900 C under cyclic conditions," Journal of Materials Processing Technology, vol. 172, no. 1, pp. 52-63, 2006.
S. S. Chatha, H. S. Sidhu, and B. S. Sidhu, "Characterisation and corrosion-erosion behaviour of carbide based thermal spray coatings," Journal of Minerals and Materials Characterization and Engineering, vol. 11, no. 06, p. 569, 2012.
A. Wong-Moreno and D. López-López, "Erosion, corrosion and deposits in gas turbines burning heavy, high sulphur fuel oil," Corrosion Reviews, vol. 14, no. 3-4, pp. 265-296, 1996.
H. Singh, D. Puri, and S. Prakash, "An overview of Na2SO4 and/or V2O5 induced hot corrosion of Fe-and Ni-based superalloys," Rev. Adv. Mater. Sci, vol. 16, no. 1-2, pp. 27-50, 2007.
M. M. Barbooti, S. H. Al-Madfai, and H. J. Nassouri, "Thermochemical studies on hot ash corrosion of stainless steel 304 and inhibition by magnesium sulphate," Thermochimica Acta, vol. 126, pp. 43-49, 1988.
K. Natesan, "Corrosion-erosion behavior of materials in a coal-gasification environment," Corrosion, vol. 32, no. 9, pp. 364-370, 1976.
B. Gleeson, "High‐Temperature Corrosion of Metallic Alloys and Coatings," Materials Science and Technology, 2000.
R. A. Rapp, "Chemistry and electrochemistry of the hot corrosion of metals," Corrosion, vol. 42, no. 10, pp. 568-577, 1986.
G. Meier, "A review of advances in high-temperature corrosion," Materials Science and Engineering: A, vol. 120, pp. 1-11, 1989.
B. Wang, "Erosion-corrosion of thermal sprayed coatings in FBC boilers," Wear, vol. 199, no. 1, pp. 24-32, 1996.
V. Chawla, "Microstructural Characteristics and Mechanical Properties of Nanostructured and Conventional TiAlN and AlCrN Coatings on ASTM-SA210 Grade A-1 Boiler Steel," ISRN Corrosion, vol. 2013, p. 14, 2013.
T. Sidhu, S. Prakash, and R. Agrawal, "Studies of the metallurgical and mechanical properties of high velocity oxy-fuel sprayed stellite-6 coatings on Ni-and Fe-based superalloys," Surface and Coatings Technology, vol. 201, no. 1-2, pp. 273-281, 2006.
B. Singh, A. Jain, and V. Chawla, "Evaluation of erosion-corrosion resistance of some detonation gun sprayed coatings on grade A-1 boiler steel in a coal fired boiler," IOSRD International Journal of Engineering, vol. 2, no. 1, pp. 13-18, 2015.
R. Unger, "Thermal spray coatings," ASM International, ASM Handbook., vol. 13, pp. 459-462, 1987.
N. Bala, H. Singh, and S. Prakash, "High Temperature Corrosion Behavior of Cold Spray Ni-20Cr Coating on Boiler Steel in Molten Salt Environment at 900 C," Journal of Thermal Spray Technology, vol. 19, no. 1-2, pp. 110-118, 2010.
K. Katiki, S. Yadlapati, and S. N. S. Chidepudi, "Comparative High Temperature Corrosion Studies on Zirconium Dioxide Coated Inconel 625 in Air and Molten Salt Environment," International Journal of ChemTech Research, vol. 6, no. 11, pp. 4579-45845, 2014.
U. Schulz, C. Leyens, K. Fritscher, M. Peters, B. Saruhan-Brings, O. Lavigne, et al., "Some recent trends in research and technology of advanced thermal barrier coatings," Aerospace Science and Technology, vol. 7, no. 1, pp. 73-80, 2003.
L. Erickson, R. Westergård, U. Wiklund, N. Axen, H. Hawthorne, and S. Hogmark, "Cohesion in plasma-sprayed coatings—a comparison between evaluation methods," Wear, vol. 214, no. 1, pp. 30-37, 1998.
B. S. Sidhu, D. Puri, and S. Prakash, "Mechanical and metallurgical properties of plasma sprayed and laser remelted Ni–20Cr and Stellite-6 coatings," Journal of Materials Processing Technology, vol. 159, no. 3, pp. 347-355, 2005.
J. KARTHIKEYAN, K. Sreekumar, N. VENKATRAMANI, and V. Rohatgi, "Preparation and characterization of plasma-sprayed thick ceramic coatings reinforced with metal pins," High Temperatures. High Pressures, vol. 20, no. 6, pp. 653-660, 1988.
A. N. Khan and J. Lu, "Thermal cyclic behavior of air plasma sprayed thermal barrier coatings sprayed on stainless steel substrates," Surface and Coatings Technology, vol. 201, no. 8, pp. 4653-4658, 2007.
L. Du, W. Zhang, W. Liu, and J. Zhang, "Preparation and characterization of plasma sprayed Ni3Al–hBN composite coating," Surface and Coatings Technology, vol. 205, no. 7, pp. 2419-2424, 2010.
N. Hegazy, M. Shoeib, S. Abdel-Samea, and H. Abdel-Kader, "'Effect of plasma sprayed alumina coating on corrosion resistance'," in Proc. 13th Int. Conf. on 'Aerospace sciences and aviation technology', Cairo, Egypt, 2009, pp. 1-10.
E. Celik, I. Ozdemir, E. Avci, and Y. Tsunekawa, "Corrosion behaviour of plasma sprayed coatings," Surface and Coatings Technology, vol. 193, no. 1, pp. 297-302, 2005.
P. Ananthapadmanabhan, K. Sreekumar, K. Muraleedharan, and N. Venkatramani, "Plasma-sprayed composite coatings for high temperature applications," Surface and Coatings Technology, vol. 49, no. 1, pp. 62-66, 1991.
S. Deshpande, A. Kulkarni, S. Sampath, and H. Herman, "Application of image analysis for characterization of porosity in thermal spray coatings and correlation with small angle neutron scattering," Surface and Coatings Technology, vol. 187, no. 1, pp. 6-16, 2004.
S. Deshpande, S. Sampath, and H. Zhang, "Mechanisms of oxidation and its role in microstructural evolution of metallic thermal spray coatings—Case study for Ni–Al," Surface and Coatings Technology, vol. 200, no. 18, pp. 5395-5406, 2006.
S. Kamal, R. Jayaganthan, and S. Prakash, "Evaluation of cyclic hot corrosion behaviour of detonation gun sprayed Cr3C2–25% NiCr coatings on nickel-and iron-based superalloys," Surface and Coatings Technology, vol. 203, no. 8, pp. 1004-1013, 2009.
M. K. Singla, H. Singh, and V. Chawla, "Thermal Sprayed CNT Reinforced Nanocomposite Coatings–A Review," J. Miner. Mater. Charact. Eng., vol. 10, no. 8, pp. 717-726, 2011.
J. Andzelm, N. Govind, and A. Maiti, "Nanotube-based gas sensors–Role of structural defects," Chemical Physics Letters, vol. 421, no. 1, pp. 58-62, 2006.
B. Yu and M. Meyyappan, "Nanotechnology: role in emerging nanoelectronics," Solid-state electronics, vol. 50, no. 4, pp. 536-544, 2006.
S. Iijima, "Helical microtubules of graphitic carbon," Nature, vol. 354, no. 6348, pp. 56-58, 1991.
Z. Han and A. Fina, "Thermal conductivity of carbon nanotubes and their polymer nanocomposites: a review," Progress in polymer science, vol. 36, no. 7, pp. 914-944, 2011.
K. Liew, X. He, and C. Wong, "On the study of elastic and plastic properties of multi-walled carbon nanotubes under axial tension using molecular dynamics simulation," Acta Materialia, vol. 52, no. 9, pp. 2521-2527, 2004.
M.-F. Yu, O. Lourie, M. J. Dyer, K. Moloni, T. F. Kelly, and R. S. Ruoff, "Strength and breaking mechanism of multiwalled carbon nanotubes under tensile load," Science, vol. 287, no. 5453, pp. 637-640, 2000.
A. Krishnan, E. Dujardin, T. Ebbesen, P. Yianilos, and M. Treacy, "Young’s modulus of single-walled nanotubes," Physical Review B, vol. 58, no. 20, p. 14013, 1998.
M. Loos, "Chapter 3 – Allotropes of Carbon and Carbon Nanotubes," in Carbon Nanotube Reinforced Composites, M. Loos, Ed., ed. Oxford: William Andrew Publishing, 2015, pp. 73-101.
X. Chen, C. Chen, H. Xiao, F. Cheng, G. Zhang, and G. Yi, "Corrosion behavior of carbon nanotubes–Ni composite coating," Surface and Coatings Technology, vol. 191, no. 2, pp. 351-356, 2005.
B. Praveen, T. Venkatesha, Y. A. Naik, and K. Prashantha, "Corrosion studies of carbon nanotubes–Zn composite coating," Surface and Coatings Technology, vol. 201, no. 12, pp. 5836-5842, 2007.
A. K. Keshri, V. Singh, J. Huang, S. Seal, W. Choi, and A. Agarwal, "Intermediate temperature tribological behavior of carbon nanotube reinforced plasma sprayed aluminum oxide coating," Surface and Coatings Technology, vol. 204, no. 11, pp. 1847-1855, 2010.
I. Ahmad, M. Unwin, H. Cao, H. Chen, H. Zhao, A. Kennedy, et al., "Multi-walled carbon nanotubes reinforced Al2O3 nanocomposites: mechanical properties and interfacial investigations," Composites Science and Technology, vol. 70, no. 8, pp. 1199-1206, 2010.
K. Balani, S. P. Harimkar, A. Keshri, Y. Chen, N. B. Dahotre, and A. Agarwal, "Multiscale wear of plasma-sprayed carbon-nanotube-reinforced aluminum oxide nanocomposite coating," Acta Materialia, vol. 56, no. 20, pp. 5984-5994, 2008.
C. F. Gutierrez-Gonzalez, A. Smirnov, A. Centeno, A. Fernández, B. Alonso, V. G. Rocha, et al., "Wear behavior of graphene/alumina composite," Ceramics International, vol. 41, no. 6, pp. 7434-7438, Jul. 2015.
M. O. Bodunrin, K. K. Alaneme, and L. H. Chown, "Aluminium matrix hybrid composites: a review of reinforcement philosophies; mechanical, corrosion and tribological characteristics," Journal of Materials Research and Technology, vol. 4, no. 4, pp. 434-445, 2015.
D. Kaewsai, A. Watcharapasorn, P. Singjai, S. Wirojanupatump, P. Niranatlumpong, and S. Jiansirisomboon, "Thermal sprayed stainless steel/carbon nanotube composite coatings," Surface and Coatings Technology, vol. 205, no. 7, pp. 2104-2112, 2010.
S. Singhal, R. Pasricha, M. Jangra, R. Chahal, S. Teotia, and R. Mathur, "Carbon nanotubes: amino functionalization and its application in the fabrication of Al-matrix composites," Powder Technology, vol. 215, pp. 254-263, 2012.
D.-S. Lim, D.-H. You, H.-J. Choi, S.-H. Lim, and H. Jang, "Effect of CNT distribution on tribological behavior of alumina–CNT composites," Wear, vol. 259, no. 1, pp. 539-544, 2005.
C. Kwok, P. Wong, F. Cheng, and H. Man, "Characterization and corrosion behavior of hydroxyapatite coatings on Ti6Al4V fabricated by electrophoretic deposition," Applied Surface Science, vol. 255, no. 13, pp. 6736-6744, 2009.
M. Mazaheri, D. Mari, Z. R. Hesabi, R. Schaller, and G. Fantozzi, "Multi-walled carbon nanotube/nanostructured zirconia composites: Outstanding mechanical properties in a wide range of temperature," Composites Science and Technology, vol. 71, no. 7, pp. 939-945, 2011.
A. K. Keshri, J. Huang, V. Singh, W. Choi, S. Seal, and A. Agarwal, "Synthesis of aluminum oxide coating with carbon nanotube reinforcement produced by chemical vapor deposition for improved fracture and wear resistance," Carbon, vol. 48, no. 2, pp. 431-442, 2010.
H. Li, Y. Xie, K. Li, L. Huang, S. Huang, B. Zhao, et al., "Microstructure and wear behavior of graphene nanosheets-reinforced zirconia coating," Ceramics International, vol. 40, no. 8, Part B, pp. 12821-12829, Sep. 2014.
G. Han, Z. Wang, K. Liu, S. Li, X. Du, and W. Du, "Synthesis of CNT-reinforced AZ31 magnesium alloy composites with uniformly distributed CNTs," Materials Science and Engineering: A, vol. 628, no. 0, pp. 350-357, Mar. 25, 2015.
S. R. Bakshi, V. Singh, K. Balani, D. G. McCartney, S. Seal, and A. Agarwal, "Carbon nanotube reinforced aluminum composite coating via cold spraying," Surface and Coatings Technology, vol. 202, no. 21, pp. 5162-5169, 2008.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2018 The Research Publication
This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
