Optimization of Process Parameters of Shot Peening for AISI 4340 Steel

Authors

  • Supinderjit Singh Assistant Professor, Department of Mechanical Engineering, Swami Vivekanand Institute of Engineering & Technology, Chandigarh, India
  • Ankur Gil Assistant Professor, Department of Mechanical Engineering, Swami Vivekanand Institute of Engineering & Technology, Chandigarh, India
  • Dhiraj Parkash Dhiman Assistant Professor, Department of Mechanical Engineering, Swami Vivekanand Institute of Engineering & Technology, Chandigarh, India

DOI:

https://doi.org/10.51983/ajeat-2018.7.1.984

Keywords:

RSM, ANOVA, Surface Hardness, Surface Roughness, Residual Stresses

Abstract

Surface modification is one of the important requirements of various components used in industrial applications. Shot peening is one of the surface modification techniques which is being widely used in automotive industry to enhance fatigue life and surface characterises of mechanical parts. In this thesis, the development of experimental set up for shot peening has been undertaken to investigate the effect of prominent process parameter on surface characterises of a given target surface. The major objective of this work is to investigate the effect of three prominent process parameters, namely Air pressure, Temperature of target surface and Stand-off distance on surface characteristics of AISI 4340 steel. The work material has been chosen keeping in view its applications in local industry related to automotive components. The performance of peening process has been measured in terms of surface hardness, surface roughness and residual stresses. An experimental design approach Response Surface Method (RSM) has been used for the design and analysis of experimental data. The effect of process parameters on performance characteristics has been depicted with the help of ANOVA. Optimal set of process parameters has been obtained on the basis of desirability approach. The optimised combination for best performance came as (Air pressure – 4.83 bars, Temperature of target surface – 30°C and stand-off distance-178 mm).

References

H. Boeckels and L. Wagner, "Effect of prior cold work on fatigue performance of shot peened Ti–2.5Cu," in V. Schulze and A. Niku-Lari (Eds.), Proceedings of the Ninth ICSP, Paris, pp. 332–337, 2005.

Y. Harada, K. Fukaura, and S. Haga, "Influence of microshot peening on surface layer characteristics of structural steel," Journal of Materials Processing Technology, vol. 191, pp. 297–301, 2007.

Y. Harada, K. Fukaura, and S. Kohamada, "Effects of microshot peening on surface characteristics of high-speed tool steel," Journal of Materials Processing Technology, vol. 201, pp. 319–324, 2008.

J. M. Champaigne, "Shot peening method," United States Champaigne, Appl. No 274, pp. 806, 1994.

U. Martin, I. Altenberger, B. Scholtes, K. Kremmer, and H. Oettel, "Cyclic deformation and near surface microstructures of normalized shot peened steel SAE 1045," Mater. Sci. Eng., A246, pp. 69–80, 1998.

T. Wanga, M. J. Platts, and J. Wu, "The optimization of shot peen forming processes," Journal of Materials Processing Technology, vol. 206, pp. 78–82, 2008.

W. Zhou, C. Jiang, X. Gan, Y. Chen, and V. Ji, "Influence of shot peening on the fatigue life of laser hardened 17-4PH steel," International Journal of Fatigue, vol. 33, pp. 549–556, 2011.

Downloads

Published

24-01-2018

How to Cite

Singh, S., Gil, A., & Dhiman, D. P. (2018). Optimization of Process Parameters of Shot Peening for AISI 4340 Steel. Asian Journal of Engineering and Applied Technology, 7(1), 1–4. https://doi.org/10.51983/ajeat-2018.7.1.984

Issue

Vol. 7 No. 1 (2018): January-June 2018

Section

Articles

License

Copyright (c) 2018 The Research Publication

Creative Commons License

This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.